Connected Mcgraw Hill Com Lesson 3
Tools:Pliers, Socket set. The fuel filter is attached to the small fuel line only. Casper from ERATH, LA. Use the advice and tips in these articles and videos to get the most out of your grass line trimmer. Substitute parts can look different from the original. Lawn & garden equipment fuel line, large.
I then attached the smaller fuel line to the carburetor. The filter ensures that no materials other than the gas is supplied to the carburetor. Any excess unused gas is sent straight back to the gas tank. Featherlite weedeater fuel line diagram. Fuel Line and Filter Replacement on a Weedeater Featherlite. Lawn & garden equipment engine carburetor diaphragm and gasket kit. 7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug.
Manufacturer substitution. There are a couple of ways to find the part or diagram you need: - Click a diagram to see the parts shown on that diagram. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Featherlite weed eater fuel line diagram for 1989 fuel selector valve. For me, now it's a matter of minutes to replace them. 4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. Pull out about 1" of fuel line from the fuel cap opening and attach filter. Push the other end of the large gas line onto the large carburetor connection.
Now you need about 3" of small fuel line which will go from the top connector of the carb to the small inlet connector on the primer bulb base. Pull the small fuel line with attached filter back into the gas tank. Featherlite weed eater fuel line diagram 24 valve. Ssgtwright2515 wrote: Since a few others have already read the (small engine repair) thread, I thought I would add this so that you all wont miss reading this. Learn about all the convenient features on our Sears PartsDirect website that make your parts purchases easier. This is a breather valve so you dont want it submerged in fuel when priming the carb.
The large fuel line is the gas return line from the carburetor. Push the large fuel line back through the hole in the gas tank about an inch. On gasoline engines, four cycle of course, truck and auto. Follow these instructions to replace the carburetor in under 30 minutes. Purchase the small and large fuel lines and filter. In the search box below, enter all or part of the part number or the part's name. The large line is the fuel return line sending excess gas back to the tank. Of course, once you get it through the hole, you'll want to pull it where you can cut the line square now to fit on the filter or whatever so always leave a little extra line to accommodate this. Replaced by #545221701? Here are the diagrams and repair parts for Weed Eater FEATHERLITE-SST-25HO-TYPE-3 gas line trimmer, as well as links to manuals and error code tables, if available. The second step is to cut the fuel line at a sharp angle so that you have a 'point' instead if a flat nub. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. Put the fuel filter onto the end of the small gas line you just pulled out of the gas tank opening. The small and large fuel lines can be replaced and refitted simply with minor skill involved.
Open the gas tank cap and pull out the gas filter. The small fuel line is the suction line providing gas to your carburetor from the gas tank. David from PALMETTO, GA. Total Repair Time:Less than 15 mins. No lubricant was necessary. We encourage you to save the model to your profile, so it's easy to access parts and manuals for your appliance whenever you log in. Replace the line back into the tank just like that because you want the fuel filter/line to flop around inside the tank. Feed the 'point' through the hole easily because it is half the size or diameter of the line. I'm a retired mechanic of 45 yrs. FEATHERLITE (Type 1) Weed Eater Trimmer - Overview. Remove any debris or broken fuel lines in the tank. 3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fall into the path of the new fuel lines installation.